add tinyusb

tinyusb/hw/bsp/waveshare_openh743i/board.mk

@@ -0,0 +1,64 @@
+UF2_FAMILY_ID = 0x6db66082
+ST_FAMILY = h7
+DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
+ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+# Default is HS port
+PORT ?= 1
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s
+LD_FILE = $(BOARD_PATH)/STM32H743IITX_FLASH.ld
+
+CFLAGS += \
+  -flto \
+  -mthumb \
+  -mabi=aapcs \
+  -mcpu=cortex-m7 \
+  -mfloat-abi=hard \
+  -mfpu=fpv5-d16 \
+  -nostdlib -nostartfiles \
+  -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \
+	-DBOARD_DEVICE_RHPORT_NUM=$(PORT) \
+  -DSTM32H743xx \
+  -DHSE_VALUE=8000000
+
+ifeq ($(PORT), 1)
+  CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
+  $(info "PORT1 High Speed")
+else
+  $(info "PORT0 Full Speed")
+endif
+
+# suppress warning caused by vendor mcu driver
+CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align
+
+# All source paths should be relative to the top level.
+SRC_C += \
+	src/portable/st/synopsys/dcd_synopsys.c \
+	$(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim_ex.c
+
+INC += \
+	$(TOP)/$(BOARD_PATH) \
+	$(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
+	$(TOP)/$(ST_CMSIS)/Include \
+	$(TOP)/$(ST_HAL_DRIVER)/Inc
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM7/r0p1
+
+# For flash-jlink target
+JLINK_DEVICE = stm32h743ii
+
+# flash target using jlink
+flash: flash-jlink