604 lines
45 KiB
C
604 lines
45 KiB
C
/**
|
|
* \file
|
|
*
|
|
* \brief Component description for SUPC
|
|
*
|
|
* Copyright (c) 2018 Microchip Technology Inc.
|
|
*
|
|
* \asf_license_start
|
|
*
|
|
* \page License
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the "License"); you may
|
|
* not use this file except in compliance with the License.
|
|
* You may obtain a copy of the Licence at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an AS IS BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*
|
|
* \asf_license_stop
|
|
*
|
|
*/
|
|
|
|
#ifndef _SAML22_SUPC_COMPONENT_
|
|
#define _SAML22_SUPC_COMPONENT_
|
|
|
|
/* ========================================================================== */
|
|
/** SOFTWARE API DEFINITION FOR SUPC */
|
|
/* ========================================================================== */
|
|
/** \addtogroup SAML22_SUPC Supply Controller */
|
|
/*@{*/
|
|
|
|
#define SUPC_U2117
|
|
#define REV_SUPC 0x300
|
|
|
|
/* -------- SUPC_INTENCLR : (SUPC Offset: 0x00) (R/W 32) Interrupt Enable Clear -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */
|
|
uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */
|
|
uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */
|
|
uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */
|
|
uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */
|
|
uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */
|
|
uint32_t :2; /*!< bit: 6.. 7 Reserved */
|
|
uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */
|
|
uint32_t APWSRDY:1; /*!< bit: 9 Automatic Power Switch Ready */
|
|
uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */
|
|
uint32_t :21; /*!< bit: 11..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_INTENCLR_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_INTENCLR_OFFSET 0x00 /**< \brief (SUPC_INTENCLR offset) Interrupt Enable Clear */
|
|
#define SUPC_INTENCLR_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_INTENCLR reset_value) Interrupt Enable Clear */
|
|
|
|
#define SUPC_INTENCLR_BOD33RDY_Pos 0 /**< \brief (SUPC_INTENCLR) BOD33 Ready */
|
|
#define SUPC_INTENCLR_BOD33RDY (_U_(0x1) << SUPC_INTENCLR_BOD33RDY_Pos)
|
|
#define SUPC_INTENCLR_BOD33DET_Pos 1 /**< \brief (SUPC_INTENCLR) BOD33 Detection */
|
|
#define SUPC_INTENCLR_BOD33DET (_U_(0x1) << SUPC_INTENCLR_BOD33DET_Pos)
|
|
#define SUPC_INTENCLR_B33SRDY_Pos 2 /**< \brief (SUPC_INTENCLR) BOD33 Synchronization Ready */
|
|
#define SUPC_INTENCLR_B33SRDY (_U_(0x1) << SUPC_INTENCLR_B33SRDY_Pos)
|
|
#define SUPC_INTENCLR_BOD12RDY_Pos 3 /**< \brief (SUPC_INTENCLR) BOD12 Ready */
|
|
#define SUPC_INTENCLR_BOD12RDY (_U_(0x1) << SUPC_INTENCLR_BOD12RDY_Pos)
|
|
#define SUPC_INTENCLR_BOD12DET_Pos 4 /**< \brief (SUPC_INTENCLR) BOD12 Detection */
|
|
#define SUPC_INTENCLR_BOD12DET (_U_(0x1) << SUPC_INTENCLR_BOD12DET_Pos)
|
|
#define SUPC_INTENCLR_B12SRDY_Pos 5 /**< \brief (SUPC_INTENCLR) BOD12 Synchronization Ready */
|
|
#define SUPC_INTENCLR_B12SRDY (_U_(0x1) << SUPC_INTENCLR_B12SRDY_Pos)
|
|
#define SUPC_INTENCLR_VREGRDY_Pos 8 /**< \brief (SUPC_INTENCLR) Voltage Regulator Ready */
|
|
#define SUPC_INTENCLR_VREGRDY (_U_(0x1) << SUPC_INTENCLR_VREGRDY_Pos)
|
|
#define SUPC_INTENCLR_APWSRDY_Pos 9 /**< \brief (SUPC_INTENCLR) Automatic Power Switch Ready */
|
|
#define SUPC_INTENCLR_APWSRDY (_U_(0x1) << SUPC_INTENCLR_APWSRDY_Pos)
|
|
#define SUPC_INTENCLR_VCORERDY_Pos 10 /**< \brief (SUPC_INTENCLR) VDDCORE Ready */
|
|
#define SUPC_INTENCLR_VCORERDY (_U_(0x1) << SUPC_INTENCLR_VCORERDY_Pos)
|
|
#define SUPC_INTENCLR_MASK _U_(0x0000073F) /**< \brief (SUPC_INTENCLR) MASK Register */
|
|
|
|
/* -------- SUPC_INTENSET : (SUPC Offset: 0x04) (R/W 32) Interrupt Enable Set -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */
|
|
uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */
|
|
uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */
|
|
uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */
|
|
uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */
|
|
uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */
|
|
uint32_t :2; /*!< bit: 6.. 7 Reserved */
|
|
uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */
|
|
uint32_t APWSRDY:1; /*!< bit: 9 Automatic Power Switch Ready */
|
|
uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */
|
|
uint32_t :21; /*!< bit: 11..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_INTENSET_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_INTENSET_OFFSET 0x04 /**< \brief (SUPC_INTENSET offset) Interrupt Enable Set */
|
|
#define SUPC_INTENSET_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_INTENSET reset_value) Interrupt Enable Set */
|
|
|
|
#define SUPC_INTENSET_BOD33RDY_Pos 0 /**< \brief (SUPC_INTENSET) BOD33 Ready */
|
|
#define SUPC_INTENSET_BOD33RDY (_U_(0x1) << SUPC_INTENSET_BOD33RDY_Pos)
|
|
#define SUPC_INTENSET_BOD33DET_Pos 1 /**< \brief (SUPC_INTENSET) BOD33 Detection */
|
|
#define SUPC_INTENSET_BOD33DET (_U_(0x1) << SUPC_INTENSET_BOD33DET_Pos)
|
|
#define SUPC_INTENSET_B33SRDY_Pos 2 /**< \brief (SUPC_INTENSET) BOD33 Synchronization Ready */
|
|
#define SUPC_INTENSET_B33SRDY (_U_(0x1) << SUPC_INTENSET_B33SRDY_Pos)
|
|
#define SUPC_INTENSET_BOD12RDY_Pos 3 /**< \brief (SUPC_INTENSET) BOD12 Ready */
|
|
#define SUPC_INTENSET_BOD12RDY (_U_(0x1) << SUPC_INTENSET_BOD12RDY_Pos)
|
|
#define SUPC_INTENSET_BOD12DET_Pos 4 /**< \brief (SUPC_INTENSET) BOD12 Detection */
|
|
#define SUPC_INTENSET_BOD12DET (_U_(0x1) << SUPC_INTENSET_BOD12DET_Pos)
|
|
#define SUPC_INTENSET_B12SRDY_Pos 5 /**< \brief (SUPC_INTENSET) BOD12 Synchronization Ready */
|
|
#define SUPC_INTENSET_B12SRDY (_U_(0x1) << SUPC_INTENSET_B12SRDY_Pos)
|
|
#define SUPC_INTENSET_VREGRDY_Pos 8 /**< \brief (SUPC_INTENSET) Voltage Regulator Ready */
|
|
#define SUPC_INTENSET_VREGRDY (_U_(0x1) << SUPC_INTENSET_VREGRDY_Pos)
|
|
#define SUPC_INTENSET_APWSRDY_Pos 9 /**< \brief (SUPC_INTENSET) Automatic Power Switch Ready */
|
|
#define SUPC_INTENSET_APWSRDY (_U_(0x1) << SUPC_INTENSET_APWSRDY_Pos)
|
|
#define SUPC_INTENSET_VCORERDY_Pos 10 /**< \brief (SUPC_INTENSET) VDDCORE Ready */
|
|
#define SUPC_INTENSET_VCORERDY (_U_(0x1) << SUPC_INTENSET_VCORERDY_Pos)
|
|
#define SUPC_INTENSET_MASK _U_(0x0000073F) /**< \brief (SUPC_INTENSET) MASK Register */
|
|
|
|
/* -------- SUPC_INTFLAG : (SUPC Offset: 0x08) (R/W 32) Interrupt Flag Status and Clear -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union { // __I to avoid read-modify-write on write-to-clear register
|
|
struct {
|
|
__I uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */
|
|
__I uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */
|
|
__I uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */
|
|
__I uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */
|
|
__I uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */
|
|
__I uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */
|
|
__I uint32_t :2; /*!< bit: 6.. 7 Reserved */
|
|
__I uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */
|
|
__I uint32_t APWSRDY:1; /*!< bit: 9 Automatic Power Switch Ready */
|
|
__I uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */
|
|
__I uint32_t :21; /*!< bit: 11..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_INTFLAG_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_INTFLAG_OFFSET 0x08 /**< \brief (SUPC_INTFLAG offset) Interrupt Flag Status and Clear */
|
|
#define SUPC_INTFLAG_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_INTFLAG reset_value) Interrupt Flag Status and Clear */
|
|
|
|
#define SUPC_INTFLAG_BOD33RDY_Pos 0 /**< \brief (SUPC_INTFLAG) BOD33 Ready */
|
|
#define SUPC_INTFLAG_BOD33RDY (_U_(0x1) << SUPC_INTFLAG_BOD33RDY_Pos)
|
|
#define SUPC_INTFLAG_BOD33DET_Pos 1 /**< \brief (SUPC_INTFLAG) BOD33 Detection */
|
|
#define SUPC_INTFLAG_BOD33DET (_U_(0x1) << SUPC_INTFLAG_BOD33DET_Pos)
|
|
#define SUPC_INTFLAG_B33SRDY_Pos 2 /**< \brief (SUPC_INTFLAG) BOD33 Synchronization Ready */
|
|
#define SUPC_INTFLAG_B33SRDY (_U_(0x1) << SUPC_INTFLAG_B33SRDY_Pos)
|
|
#define SUPC_INTFLAG_BOD12RDY_Pos 3 /**< \brief (SUPC_INTFLAG) BOD12 Ready */
|
|
#define SUPC_INTFLAG_BOD12RDY (_U_(0x1) << SUPC_INTFLAG_BOD12RDY_Pos)
|
|
#define SUPC_INTFLAG_BOD12DET_Pos 4 /**< \brief (SUPC_INTFLAG) BOD12 Detection */
|
|
#define SUPC_INTFLAG_BOD12DET (_U_(0x1) << SUPC_INTFLAG_BOD12DET_Pos)
|
|
#define SUPC_INTFLAG_B12SRDY_Pos 5 /**< \brief (SUPC_INTFLAG) BOD12 Synchronization Ready */
|
|
#define SUPC_INTFLAG_B12SRDY (_U_(0x1) << SUPC_INTFLAG_B12SRDY_Pos)
|
|
#define SUPC_INTFLAG_VREGRDY_Pos 8 /**< \brief (SUPC_INTFLAG) Voltage Regulator Ready */
|
|
#define SUPC_INTFLAG_VREGRDY (_U_(0x1) << SUPC_INTFLAG_VREGRDY_Pos)
|
|
#define SUPC_INTFLAG_APWSRDY_Pos 9 /**< \brief (SUPC_INTFLAG) Automatic Power Switch Ready */
|
|
#define SUPC_INTFLAG_APWSRDY (_U_(0x1) << SUPC_INTFLAG_APWSRDY_Pos)
|
|
#define SUPC_INTFLAG_VCORERDY_Pos 10 /**< \brief (SUPC_INTFLAG) VDDCORE Ready */
|
|
#define SUPC_INTFLAG_VCORERDY (_U_(0x1) << SUPC_INTFLAG_VCORERDY_Pos)
|
|
#define SUPC_INTFLAG_MASK _U_(0x0000073F) /**< \brief (SUPC_INTFLAG) MASK Register */
|
|
|
|
/* -------- SUPC_STATUS : (SUPC Offset: 0x0C) (R/ 32) Power and Clocks Status -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t BOD33RDY:1; /*!< bit: 0 BOD33 Ready */
|
|
uint32_t BOD33DET:1; /*!< bit: 1 BOD33 Detection */
|
|
uint32_t B33SRDY:1; /*!< bit: 2 BOD33 Synchronization Ready */
|
|
uint32_t BOD12RDY:1; /*!< bit: 3 BOD12 Ready */
|
|
uint32_t BOD12DET:1; /*!< bit: 4 BOD12 Detection */
|
|
uint32_t B12SRDY:1; /*!< bit: 5 BOD12 Synchronization Ready */
|
|
uint32_t :2; /*!< bit: 6.. 7 Reserved */
|
|
uint32_t VREGRDY:1; /*!< bit: 8 Voltage Regulator Ready */
|
|
uint32_t APWSRDY:1; /*!< bit: 9 Automatic Power Switch Ready */
|
|
uint32_t VCORERDY:1; /*!< bit: 10 VDDCORE Ready */
|
|
uint32_t BBPS:1; /*!< bit: 11 Battery Backup Power Switch */
|
|
uint32_t :20; /*!< bit: 12..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_STATUS_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_STATUS_OFFSET 0x0C /**< \brief (SUPC_STATUS offset) Power and Clocks Status */
|
|
#define SUPC_STATUS_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_STATUS reset_value) Power and Clocks Status */
|
|
|
|
#define SUPC_STATUS_BOD33RDY_Pos 0 /**< \brief (SUPC_STATUS) BOD33 Ready */
|
|
#define SUPC_STATUS_BOD33RDY (_U_(0x1) << SUPC_STATUS_BOD33RDY_Pos)
|
|
#define SUPC_STATUS_BOD33DET_Pos 1 /**< \brief (SUPC_STATUS) BOD33 Detection */
|
|
#define SUPC_STATUS_BOD33DET (_U_(0x1) << SUPC_STATUS_BOD33DET_Pos)
|
|
#define SUPC_STATUS_B33SRDY_Pos 2 /**< \brief (SUPC_STATUS) BOD33 Synchronization Ready */
|
|
#define SUPC_STATUS_B33SRDY (_U_(0x1) << SUPC_STATUS_B33SRDY_Pos)
|
|
#define SUPC_STATUS_BOD12RDY_Pos 3 /**< \brief (SUPC_STATUS) BOD12 Ready */
|
|
#define SUPC_STATUS_BOD12RDY (_U_(0x1) << SUPC_STATUS_BOD12RDY_Pos)
|
|
#define SUPC_STATUS_BOD12DET_Pos 4 /**< \brief (SUPC_STATUS) BOD12 Detection */
|
|
#define SUPC_STATUS_BOD12DET (_U_(0x1) << SUPC_STATUS_BOD12DET_Pos)
|
|
#define SUPC_STATUS_B12SRDY_Pos 5 /**< \brief (SUPC_STATUS) BOD12 Synchronization Ready */
|
|
#define SUPC_STATUS_B12SRDY (_U_(0x1) << SUPC_STATUS_B12SRDY_Pos)
|
|
#define SUPC_STATUS_VREGRDY_Pos 8 /**< \brief (SUPC_STATUS) Voltage Regulator Ready */
|
|
#define SUPC_STATUS_VREGRDY (_U_(0x1) << SUPC_STATUS_VREGRDY_Pos)
|
|
#define SUPC_STATUS_APWSRDY_Pos 9 /**< \brief (SUPC_STATUS) Automatic Power Switch Ready */
|
|
#define SUPC_STATUS_APWSRDY (_U_(0x1) << SUPC_STATUS_APWSRDY_Pos)
|
|
#define SUPC_STATUS_VCORERDY_Pos 10 /**< \brief (SUPC_STATUS) VDDCORE Ready */
|
|
#define SUPC_STATUS_VCORERDY (_U_(0x1) << SUPC_STATUS_VCORERDY_Pos)
|
|
#define SUPC_STATUS_BBPS_Pos 11 /**< \brief (SUPC_STATUS) Battery Backup Power Switch */
|
|
#define SUPC_STATUS_BBPS (_U_(0x1) << SUPC_STATUS_BBPS_Pos)
|
|
#define SUPC_STATUS_MASK _U_(0x00000F3F) /**< \brief (SUPC_STATUS) MASK Register */
|
|
|
|
/* -------- SUPC_BOD33 : (SUPC Offset: 0x10) (R/W 32) BOD33 Control -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t :1; /*!< bit: 0 Reserved */
|
|
uint32_t ENABLE:1; /*!< bit: 1 Enable */
|
|
uint32_t HYST:1; /*!< bit: 2 Hysteresis Enable */
|
|
uint32_t ACTION:2; /*!< bit: 3.. 4 Action when Threshold Crossed */
|
|
uint32_t STDBYCFG:1; /*!< bit: 5 Configuration in Standby mode */
|
|
uint32_t RUNSTDBY:1; /*!< bit: 6 Run during Standby */
|
|
uint32_t RUNBKUP:1; /*!< bit: 7 Configuration in Backup mode */
|
|
uint32_t ACTCFG:1; /*!< bit: 8 Configuration in Active mode */
|
|
uint32_t :1; /*!< bit: 9 Reserved */
|
|
uint32_t VMON:1; /*!< bit: 10 Voltage Monitored in active and standby mode */
|
|
uint32_t :1; /*!< bit: 11 Reserved */
|
|
uint32_t PSEL:4; /*!< bit: 12..15 Prescaler Select */
|
|
uint32_t LEVEL:6; /*!< bit: 16..21 Threshold Level for VDD */
|
|
uint32_t :2; /*!< bit: 22..23 Reserved */
|
|
uint32_t BKUPLEVEL:6; /*!< bit: 24..29 Threshold Level in backup sleep mode or for VBAT */
|
|
uint32_t :2; /*!< bit: 30..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_BOD33_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_BOD33_OFFSET 0x10 /**< \brief (SUPC_BOD33 offset) BOD33 Control */
|
|
#define SUPC_BOD33_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BOD33 reset_value) BOD33 Control */
|
|
|
|
#define SUPC_BOD33_ENABLE_Pos 1 /**< \brief (SUPC_BOD33) Enable */
|
|
#define SUPC_BOD33_ENABLE (_U_(0x1) << SUPC_BOD33_ENABLE_Pos)
|
|
#define SUPC_BOD33_HYST_Pos 2 /**< \brief (SUPC_BOD33) Hysteresis Enable */
|
|
#define SUPC_BOD33_HYST (_U_(0x1) << SUPC_BOD33_HYST_Pos)
|
|
#define SUPC_BOD33_ACTION_Pos 3 /**< \brief (SUPC_BOD33) Action when Threshold Crossed */
|
|
#define SUPC_BOD33_ACTION_Msk (_U_(0x3) << SUPC_BOD33_ACTION_Pos)
|
|
#define SUPC_BOD33_ACTION(value) (SUPC_BOD33_ACTION_Msk & ((value) << SUPC_BOD33_ACTION_Pos))
|
|
#define SUPC_BOD33_ACTION_NONE_Val _U_(0x0) /**< \brief (SUPC_BOD33) No action */
|
|
#define SUPC_BOD33_ACTION_RESET_Val _U_(0x1) /**< \brief (SUPC_BOD33) The BOD33 generates a reset */
|
|
#define SUPC_BOD33_ACTION_INT_Val _U_(0x2) /**< \brief (SUPC_BOD33) The BOD33 generates an interrupt */
|
|
#define SUPC_BOD33_ACTION_BKUP_Val _U_(0x3) /**< \brief (SUPC_BOD33) The BOD33 puts the device in backup sleep mode if VMON=0 */
|
|
#define SUPC_BOD33_ACTION_NONE (SUPC_BOD33_ACTION_NONE_Val << SUPC_BOD33_ACTION_Pos)
|
|
#define SUPC_BOD33_ACTION_RESET (SUPC_BOD33_ACTION_RESET_Val << SUPC_BOD33_ACTION_Pos)
|
|
#define SUPC_BOD33_ACTION_INT (SUPC_BOD33_ACTION_INT_Val << SUPC_BOD33_ACTION_Pos)
|
|
#define SUPC_BOD33_ACTION_BKUP (SUPC_BOD33_ACTION_BKUP_Val << SUPC_BOD33_ACTION_Pos)
|
|
#define SUPC_BOD33_STDBYCFG_Pos 5 /**< \brief (SUPC_BOD33) Configuration in Standby mode */
|
|
#define SUPC_BOD33_STDBYCFG (_U_(0x1) << SUPC_BOD33_STDBYCFG_Pos)
|
|
#define SUPC_BOD33_RUNSTDBY_Pos 6 /**< \brief (SUPC_BOD33) Run during Standby */
|
|
#define SUPC_BOD33_RUNSTDBY (_U_(0x1) << SUPC_BOD33_RUNSTDBY_Pos)
|
|
#define SUPC_BOD33_RUNBKUP_Pos 7 /**< \brief (SUPC_BOD33) Configuration in Backup mode */
|
|
#define SUPC_BOD33_RUNBKUP (_U_(0x1) << SUPC_BOD33_RUNBKUP_Pos)
|
|
#define SUPC_BOD33_ACTCFG_Pos 8 /**< \brief (SUPC_BOD33) Configuration in Active mode */
|
|
#define SUPC_BOD33_ACTCFG (_U_(0x1) << SUPC_BOD33_ACTCFG_Pos)
|
|
#define SUPC_BOD33_VMON_Pos 10 /**< \brief (SUPC_BOD33) Voltage Monitored in active and standby mode */
|
|
#define SUPC_BOD33_VMON (_U_(0x1) << SUPC_BOD33_VMON_Pos)
|
|
#define SUPC_BOD33_PSEL_Pos 12 /**< \brief (SUPC_BOD33) Prescaler Select */
|
|
#define SUPC_BOD33_PSEL_Msk (_U_(0xF) << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL(value) (SUPC_BOD33_PSEL_Msk & ((value) << SUPC_BOD33_PSEL_Pos))
|
|
#define SUPC_BOD33_PSEL_DIV2_Val _U_(0x0) /**< \brief (SUPC_BOD33) Divide clock by 2 */
|
|
#define SUPC_BOD33_PSEL_DIV4_Val _U_(0x1) /**< \brief (SUPC_BOD33) Divide clock by 4 */
|
|
#define SUPC_BOD33_PSEL_DIV8_Val _U_(0x2) /**< \brief (SUPC_BOD33) Divide clock by 8 */
|
|
#define SUPC_BOD33_PSEL_DIV16_Val _U_(0x3) /**< \brief (SUPC_BOD33) Divide clock by 16 */
|
|
#define SUPC_BOD33_PSEL_DIV32_Val _U_(0x4) /**< \brief (SUPC_BOD33) Divide clock by 32 */
|
|
#define SUPC_BOD33_PSEL_DIV64_Val _U_(0x5) /**< \brief (SUPC_BOD33) Divide clock by 64 */
|
|
#define SUPC_BOD33_PSEL_DIV128_Val _U_(0x6) /**< \brief (SUPC_BOD33) Divide clock by 128 */
|
|
#define SUPC_BOD33_PSEL_DIV256_Val _U_(0x7) /**< \brief (SUPC_BOD33) Divide clock by 256 */
|
|
#define SUPC_BOD33_PSEL_DIV512_Val _U_(0x8) /**< \brief (SUPC_BOD33) Divide clock by 512 */
|
|
#define SUPC_BOD33_PSEL_DIV1024_Val _U_(0x9) /**< \brief (SUPC_BOD33) Divide clock by 1024 */
|
|
#define SUPC_BOD33_PSEL_DIV2048_Val _U_(0xA) /**< \brief (SUPC_BOD33) Divide clock by 2048 */
|
|
#define SUPC_BOD33_PSEL_DIV4096_Val _U_(0xB) /**< \brief (SUPC_BOD33) Divide clock by 4096 */
|
|
#define SUPC_BOD33_PSEL_DIV8192_Val _U_(0xC) /**< \brief (SUPC_BOD33) Divide clock by 8192 */
|
|
#define SUPC_BOD33_PSEL_DIV16384_Val _U_(0xD) /**< \brief (SUPC_BOD33) Divide clock by 16384 */
|
|
#define SUPC_BOD33_PSEL_DIV32768_Val _U_(0xE) /**< \brief (SUPC_BOD33) Divide clock by 32768 */
|
|
#define SUPC_BOD33_PSEL_DIV65536_Val _U_(0xF) /**< \brief (SUPC_BOD33) Divide clock by 65536 */
|
|
#define SUPC_BOD33_PSEL_DIV2 (SUPC_BOD33_PSEL_DIV2_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV4 (SUPC_BOD33_PSEL_DIV4_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV8 (SUPC_BOD33_PSEL_DIV8_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV16 (SUPC_BOD33_PSEL_DIV16_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV32 (SUPC_BOD33_PSEL_DIV32_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV64 (SUPC_BOD33_PSEL_DIV64_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV128 (SUPC_BOD33_PSEL_DIV128_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV256 (SUPC_BOD33_PSEL_DIV256_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV512 (SUPC_BOD33_PSEL_DIV512_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV1024 (SUPC_BOD33_PSEL_DIV1024_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV2048 (SUPC_BOD33_PSEL_DIV2048_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV4096 (SUPC_BOD33_PSEL_DIV4096_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV8192 (SUPC_BOD33_PSEL_DIV8192_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV16384 (SUPC_BOD33_PSEL_DIV16384_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV32768 (SUPC_BOD33_PSEL_DIV32768_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_PSEL_DIV65536 (SUPC_BOD33_PSEL_DIV65536_Val << SUPC_BOD33_PSEL_Pos)
|
|
#define SUPC_BOD33_LEVEL_Pos 16 /**< \brief (SUPC_BOD33) Threshold Level for VDD */
|
|
#define SUPC_BOD33_LEVEL_Msk (_U_(0x3F) << SUPC_BOD33_LEVEL_Pos)
|
|
#define SUPC_BOD33_LEVEL(value) (SUPC_BOD33_LEVEL_Msk & ((value) << SUPC_BOD33_LEVEL_Pos))
|
|
#define SUPC_BOD33_BKUPLEVEL_Pos 24 /**< \brief (SUPC_BOD33) Threshold Level in backup sleep mode or for VBAT */
|
|
#define SUPC_BOD33_BKUPLEVEL_Msk (_U_(0x3F) << SUPC_BOD33_BKUPLEVEL_Pos)
|
|
#define SUPC_BOD33_BKUPLEVEL(value) (SUPC_BOD33_BKUPLEVEL_Msk & ((value) << SUPC_BOD33_BKUPLEVEL_Pos))
|
|
#define SUPC_BOD33_MASK _U_(0x3F3FF5FE) /**< \brief (SUPC_BOD33) MASK Register */
|
|
|
|
/* -------- SUPC_BOD12 : (SUPC Offset: 0x14) (R/W 32) BOD12 Control -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t :1; /*!< bit: 0 Reserved */
|
|
uint32_t ENABLE:1; /*!< bit: 1 Enable */
|
|
uint32_t HYST:1; /*!< bit: 2 Hysteresis Enable */
|
|
uint32_t ACTION:2; /*!< bit: 3.. 4 Action when Threshold Crossed */
|
|
uint32_t STDBYCFG:1; /*!< bit: 5 Configuration in Standby mode */
|
|
uint32_t RUNSTDBY:1; /*!< bit: 6 Run during Standby */
|
|
uint32_t :1; /*!< bit: 7 Reserved */
|
|
uint32_t ACTCFG:1; /*!< bit: 8 Configuration in Active mode */
|
|
uint32_t :3; /*!< bit: 9..11 Reserved */
|
|
uint32_t PSEL:4; /*!< bit: 12..15 Prescaler Select */
|
|
uint32_t LEVEL:6; /*!< bit: 16..21 Threshold Level */
|
|
uint32_t :10; /*!< bit: 22..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_BOD12_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_BOD12_OFFSET 0x14 /**< \brief (SUPC_BOD12 offset) BOD12 Control */
|
|
#define SUPC_BOD12_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BOD12 reset_value) BOD12 Control */
|
|
|
|
#define SUPC_BOD12_ENABLE_Pos 1 /**< \brief (SUPC_BOD12) Enable */
|
|
#define SUPC_BOD12_ENABLE (_U_(0x1) << SUPC_BOD12_ENABLE_Pos)
|
|
#define SUPC_BOD12_HYST_Pos 2 /**< \brief (SUPC_BOD12) Hysteresis Enable */
|
|
#define SUPC_BOD12_HYST (_U_(0x1) << SUPC_BOD12_HYST_Pos)
|
|
#define SUPC_BOD12_ACTION_Pos 3 /**< \brief (SUPC_BOD12) Action when Threshold Crossed */
|
|
#define SUPC_BOD12_ACTION_Msk (_U_(0x3) << SUPC_BOD12_ACTION_Pos)
|
|
#define SUPC_BOD12_ACTION(value) (SUPC_BOD12_ACTION_Msk & ((value) << SUPC_BOD12_ACTION_Pos))
|
|
#define SUPC_BOD12_ACTION_NONE_Val _U_(0x0) /**< \brief (SUPC_BOD12) No action */
|
|
#define SUPC_BOD12_ACTION_RESET_Val _U_(0x1) /**< \brief (SUPC_BOD12) The BOD12 generates a reset */
|
|
#define SUPC_BOD12_ACTION_INT_Val _U_(0x2) /**< \brief (SUPC_BOD12) The BOD12 generates an interrupt */
|
|
#define SUPC_BOD12_ACTION_NONE (SUPC_BOD12_ACTION_NONE_Val << SUPC_BOD12_ACTION_Pos)
|
|
#define SUPC_BOD12_ACTION_RESET (SUPC_BOD12_ACTION_RESET_Val << SUPC_BOD12_ACTION_Pos)
|
|
#define SUPC_BOD12_ACTION_INT (SUPC_BOD12_ACTION_INT_Val << SUPC_BOD12_ACTION_Pos)
|
|
#define SUPC_BOD12_STDBYCFG_Pos 5 /**< \brief (SUPC_BOD12) Configuration in Standby mode */
|
|
#define SUPC_BOD12_STDBYCFG (_U_(0x1) << SUPC_BOD12_STDBYCFG_Pos)
|
|
#define SUPC_BOD12_RUNSTDBY_Pos 6 /**< \brief (SUPC_BOD12) Run during Standby */
|
|
#define SUPC_BOD12_RUNSTDBY (_U_(0x1) << SUPC_BOD12_RUNSTDBY_Pos)
|
|
#define SUPC_BOD12_ACTCFG_Pos 8 /**< \brief (SUPC_BOD12) Configuration in Active mode */
|
|
#define SUPC_BOD12_ACTCFG (_U_(0x1) << SUPC_BOD12_ACTCFG_Pos)
|
|
#define SUPC_BOD12_PSEL_Pos 12 /**< \brief (SUPC_BOD12) Prescaler Select */
|
|
#define SUPC_BOD12_PSEL_Msk (_U_(0xF) << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL(value) (SUPC_BOD12_PSEL_Msk & ((value) << SUPC_BOD12_PSEL_Pos))
|
|
#define SUPC_BOD12_PSEL_DIV2_Val _U_(0x0) /**< \brief (SUPC_BOD12) Divide clock by 2 */
|
|
#define SUPC_BOD12_PSEL_DIV4_Val _U_(0x1) /**< \brief (SUPC_BOD12) Divide clock by 4 */
|
|
#define SUPC_BOD12_PSEL_DIV8_Val _U_(0x2) /**< \brief (SUPC_BOD12) Divide clock by 8 */
|
|
#define SUPC_BOD12_PSEL_DIV16_Val _U_(0x3) /**< \brief (SUPC_BOD12) Divide clock by 16 */
|
|
#define SUPC_BOD12_PSEL_DIV32_Val _U_(0x4) /**< \brief (SUPC_BOD12) Divide clock by 32 */
|
|
#define SUPC_BOD12_PSEL_DIV64_Val _U_(0x5) /**< \brief (SUPC_BOD12) Divide clock by 64 */
|
|
#define SUPC_BOD12_PSEL_DIV128_Val _U_(0x6) /**< \brief (SUPC_BOD12) Divide clock by 128 */
|
|
#define SUPC_BOD12_PSEL_DIV256_Val _U_(0x7) /**< \brief (SUPC_BOD12) Divide clock by 256 */
|
|
#define SUPC_BOD12_PSEL_DIV512_Val _U_(0x8) /**< \brief (SUPC_BOD12) Divide clock by 512 */
|
|
#define SUPC_BOD12_PSEL_DIV1024_Val _U_(0x9) /**< \brief (SUPC_BOD12) Divide clock by 1024 */
|
|
#define SUPC_BOD12_PSEL_DIV2048_Val _U_(0xA) /**< \brief (SUPC_BOD12) Divide clock by 2048 */
|
|
#define SUPC_BOD12_PSEL_DIV4096_Val _U_(0xB) /**< \brief (SUPC_BOD12) Divide clock by 4096 */
|
|
#define SUPC_BOD12_PSEL_DIV8192_Val _U_(0xC) /**< \brief (SUPC_BOD12) Divide clock by 8192 */
|
|
#define SUPC_BOD12_PSEL_DIV16384_Val _U_(0xD) /**< \brief (SUPC_BOD12) Divide clock by 16384 */
|
|
#define SUPC_BOD12_PSEL_DIV32768_Val _U_(0xE) /**< \brief (SUPC_BOD12) Divide clock by 32768 */
|
|
#define SUPC_BOD12_PSEL_DIV65536_Val _U_(0xF) /**< \brief (SUPC_BOD12) Divide clock by 65536 */
|
|
#define SUPC_BOD12_PSEL_DIV2 (SUPC_BOD12_PSEL_DIV2_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV4 (SUPC_BOD12_PSEL_DIV4_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV8 (SUPC_BOD12_PSEL_DIV8_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV16 (SUPC_BOD12_PSEL_DIV16_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV32 (SUPC_BOD12_PSEL_DIV32_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV64 (SUPC_BOD12_PSEL_DIV64_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV128 (SUPC_BOD12_PSEL_DIV128_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV256 (SUPC_BOD12_PSEL_DIV256_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV512 (SUPC_BOD12_PSEL_DIV512_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV1024 (SUPC_BOD12_PSEL_DIV1024_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV2048 (SUPC_BOD12_PSEL_DIV2048_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV4096 (SUPC_BOD12_PSEL_DIV4096_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV8192 (SUPC_BOD12_PSEL_DIV8192_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV16384 (SUPC_BOD12_PSEL_DIV16384_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV32768 (SUPC_BOD12_PSEL_DIV32768_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_PSEL_DIV65536 (SUPC_BOD12_PSEL_DIV65536_Val << SUPC_BOD12_PSEL_Pos)
|
|
#define SUPC_BOD12_LEVEL_Pos 16 /**< \brief (SUPC_BOD12) Threshold Level */
|
|
#define SUPC_BOD12_LEVEL_Msk (_U_(0x3F) << SUPC_BOD12_LEVEL_Pos)
|
|
#define SUPC_BOD12_LEVEL(value) (SUPC_BOD12_LEVEL_Msk & ((value) << SUPC_BOD12_LEVEL_Pos))
|
|
#define SUPC_BOD12_MASK _U_(0x003FF17E) /**< \brief (SUPC_BOD12) MASK Register */
|
|
|
|
/* -------- SUPC_VREG : (SUPC Offset: 0x18) (R/W 32) VREG Control -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t :1; /*!< bit: 0 Reserved */
|
|
uint32_t ENABLE:1; /*!< bit: 1 Enable */
|
|
uint32_t SEL:2; /*!< bit: 2.. 3 Voltage Regulator Selection in active mode */
|
|
uint32_t :1; /*!< bit: 4 Reserved */
|
|
uint32_t STDBYPL0:1; /*!< bit: 5 Standby in PL0 */
|
|
uint32_t RUNSTDBY:1; /*!< bit: 6 Run during Standby */
|
|
uint32_t :1; /*!< bit: 7 Reserved */
|
|
uint32_t LPEFF:1; /*!< bit: 8 Low Power efficiency */
|
|
uint32_t :7; /*!< bit: 9..15 Reserved */
|
|
uint32_t VSVSTEP:4; /*!< bit: 16..19 Voltage Scaling Voltage Step */
|
|
uint32_t :4; /*!< bit: 20..23 Reserved */
|
|
uint32_t VSPER:8; /*!< bit: 24..31 Voltage Scaling Period */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_VREG_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_VREG_OFFSET 0x18 /**< \brief (SUPC_VREG offset) VREG Control */
|
|
#define SUPC_VREG_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_VREG reset_value) VREG Control */
|
|
|
|
#define SUPC_VREG_ENABLE_Pos 1 /**< \brief (SUPC_VREG) Enable */
|
|
#define SUPC_VREG_ENABLE (_U_(0x1) << SUPC_VREG_ENABLE_Pos)
|
|
#define SUPC_VREG_SEL_Pos 2 /**< \brief (SUPC_VREG) Voltage Regulator Selection in active mode */
|
|
#define SUPC_VREG_SEL_Msk (_U_(0x3) << SUPC_VREG_SEL_Pos)
|
|
#define SUPC_VREG_SEL(value) (SUPC_VREG_SEL_Msk & ((value) << SUPC_VREG_SEL_Pos))
|
|
#define SUPC_VREG_SEL_LDO_Val _U_(0x0) /**< \brief (SUPC_VREG) LDO selection */
|
|
#define SUPC_VREG_SEL_BUCK_Val _U_(0x1) /**< \brief (SUPC_VREG) Buck selection */
|
|
#define SUPC_VREG_SEL_SCVREG_Val _U_(0x2) /**< \brief (SUPC_VREG) Switched Cap selection */
|
|
#define SUPC_VREG_SEL_LDO (SUPC_VREG_SEL_LDO_Val << SUPC_VREG_SEL_Pos)
|
|
#define SUPC_VREG_SEL_BUCK (SUPC_VREG_SEL_BUCK_Val << SUPC_VREG_SEL_Pos)
|
|
#define SUPC_VREG_SEL_SCVREG (SUPC_VREG_SEL_SCVREG_Val << SUPC_VREG_SEL_Pos)
|
|
#define SUPC_VREG_STDBYPL0_Pos 5 /**< \brief (SUPC_VREG) Standby in PL0 */
|
|
#define SUPC_VREG_STDBYPL0 (_U_(0x1) << SUPC_VREG_STDBYPL0_Pos)
|
|
#define SUPC_VREG_RUNSTDBY_Pos 6 /**< \brief (SUPC_VREG) Run during Standby */
|
|
#define SUPC_VREG_RUNSTDBY (_U_(0x1) << SUPC_VREG_RUNSTDBY_Pos)
|
|
#define SUPC_VREG_LPEFF_Pos 8 /**< \brief (SUPC_VREG) Low Power efficiency */
|
|
#define SUPC_VREG_LPEFF (_U_(0x1) << SUPC_VREG_LPEFF_Pos)
|
|
#define SUPC_VREG_VSVSTEP_Pos 16 /**< \brief (SUPC_VREG) Voltage Scaling Voltage Step */
|
|
#define SUPC_VREG_VSVSTEP_Msk (_U_(0xF) << SUPC_VREG_VSVSTEP_Pos)
|
|
#define SUPC_VREG_VSVSTEP(value) (SUPC_VREG_VSVSTEP_Msk & ((value) << SUPC_VREG_VSVSTEP_Pos))
|
|
#define SUPC_VREG_VSPER_Pos 24 /**< \brief (SUPC_VREG) Voltage Scaling Period */
|
|
#define SUPC_VREG_VSPER_Msk (_U_(0xFF) << SUPC_VREG_VSPER_Pos)
|
|
#define SUPC_VREG_VSPER(value) (SUPC_VREG_VSPER_Msk & ((value) << SUPC_VREG_VSPER_Pos))
|
|
#define SUPC_VREG_MASK _U_(0xFF0F016E) /**< \brief (SUPC_VREG) MASK Register */
|
|
|
|
/* -------- SUPC_VREF : (SUPC Offset: 0x1C) (R/W 32) VREF Control -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t :1; /*!< bit: 0 Reserved */
|
|
uint32_t TSEN:1; /*!< bit: 1 Temperature Sensor Output Enable */
|
|
uint32_t VREFOE:1; /*!< bit: 2 Voltage Reference Output Enable */
|
|
uint32_t TSSEL:1; /*!< bit: 3 Temperature Sensor Selection */
|
|
uint32_t :2; /*!< bit: 4.. 5 Reserved */
|
|
uint32_t RUNSTDBY:1; /*!< bit: 6 Run during Standby */
|
|
uint32_t ONDEMAND:1; /*!< bit: 7 On Demand Contrl */
|
|
uint32_t :8; /*!< bit: 8..15 Reserved */
|
|
uint32_t SEL:4; /*!< bit: 16..19 Voltage Reference Selection */
|
|
uint32_t :12; /*!< bit: 20..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_VREF_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_VREF_OFFSET 0x1C /**< \brief (SUPC_VREF offset) VREF Control */
|
|
#define SUPC_VREF_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_VREF reset_value) VREF Control */
|
|
|
|
#define SUPC_VREF_TSEN_Pos 1 /**< \brief (SUPC_VREF) Temperature Sensor Output Enable */
|
|
#define SUPC_VREF_TSEN (_U_(0x1) << SUPC_VREF_TSEN_Pos)
|
|
#define SUPC_VREF_VREFOE_Pos 2 /**< \brief (SUPC_VREF) Voltage Reference Output Enable */
|
|
#define SUPC_VREF_VREFOE (_U_(0x1) << SUPC_VREF_VREFOE_Pos)
|
|
#define SUPC_VREF_TSSEL_Pos 3 /**< \brief (SUPC_VREF) Temperature Sensor Selection */
|
|
#define SUPC_VREF_TSSEL (_U_(0x1) << SUPC_VREF_TSSEL_Pos)
|
|
#define SUPC_VREF_RUNSTDBY_Pos 6 /**< \brief (SUPC_VREF) Run during Standby */
|
|
#define SUPC_VREF_RUNSTDBY (_U_(0x1) << SUPC_VREF_RUNSTDBY_Pos)
|
|
#define SUPC_VREF_ONDEMAND_Pos 7 /**< \brief (SUPC_VREF) On Demand Contrl */
|
|
#define SUPC_VREF_ONDEMAND (_U_(0x1) << SUPC_VREF_ONDEMAND_Pos)
|
|
#define SUPC_VREF_SEL_Pos 16 /**< \brief (SUPC_VREF) Voltage Reference Selection */
|
|
#define SUPC_VREF_SEL_Msk (_U_(0xF) << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL(value) (SUPC_VREF_SEL_Msk & ((value) << SUPC_VREF_SEL_Pos))
|
|
#define SUPC_VREF_SEL_1V0_Val _U_(0x0) /**< \brief (SUPC_VREF) 1.0V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_1V1_Val _U_(0x1) /**< \brief (SUPC_VREF) 1.1V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_1V2_Val _U_(0x2) /**< \brief (SUPC_VREF) 1.2V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_1V25_Val _U_(0x3) /**< \brief (SUPC_VREF) 1.25V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_2V0_Val _U_(0x4) /**< \brief (SUPC_VREF) 2.0V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_2V2_Val _U_(0x5) /**< \brief (SUPC_VREF) 2.2V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_2V4_Val _U_(0x6) /**< \brief (SUPC_VREF) 2.4V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_2V5_Val _U_(0x7) /**< \brief (SUPC_VREF) 2.5V voltage reference typical value */
|
|
#define SUPC_VREF_SEL_1V0 (SUPC_VREF_SEL_1V0_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_1V1 (SUPC_VREF_SEL_1V1_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_1V2 (SUPC_VREF_SEL_1V2_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_1V25 (SUPC_VREF_SEL_1V25_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_2V0 (SUPC_VREF_SEL_2V0_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_2V2 (SUPC_VREF_SEL_2V2_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_2V4 (SUPC_VREF_SEL_2V4_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_SEL_2V5 (SUPC_VREF_SEL_2V5_Val << SUPC_VREF_SEL_Pos)
|
|
#define SUPC_VREF_MASK _U_(0x000F00CE) /**< \brief (SUPC_VREF) MASK Register */
|
|
|
|
/* -------- SUPC_BBPS : (SUPC Offset: 0x20) (R/W 32) Battery Backup Power Switch -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t CONF:2; /*!< bit: 0.. 1 Battery Backup Configuration */
|
|
uint32_t WAKEEN:1; /*!< bit: 2 Wake Enable */
|
|
uint32_t PSOKEN:1; /*!< bit: 3 Power Supply OK Enable */
|
|
uint32_t :28; /*!< bit: 4..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_BBPS_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_BBPS_OFFSET 0x20 /**< \brief (SUPC_BBPS offset) Battery Backup Power Switch */
|
|
#define SUPC_BBPS_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BBPS reset_value) Battery Backup Power Switch */
|
|
|
|
#define SUPC_BBPS_CONF_Pos 0 /**< \brief (SUPC_BBPS) Battery Backup Configuration */
|
|
#define SUPC_BBPS_CONF_Msk (_U_(0x3) << SUPC_BBPS_CONF_Pos)
|
|
#define SUPC_BBPS_CONF(value) (SUPC_BBPS_CONF_Msk & ((value) << SUPC_BBPS_CONF_Pos))
|
|
#define SUPC_BBPS_CONF_NONE_Val _U_(0x0) /**< \brief (SUPC_BBPS) The backup domain is always supplied by main power */
|
|
#define SUPC_BBPS_CONF_APWS_Val _U_(0x1) /**< \brief (SUPC_BBPS) The power switch is handled by the automatic power switch */
|
|
#define SUPC_BBPS_CONF_FORCED_Val _U_(0x2) /**< \brief (SUPC_BBPS) The backup domain is always supplied by battery backup power */
|
|
#define SUPC_BBPS_CONF_BOD33_Val _U_(0x3) /**< \brief (SUPC_BBPS) The power switch is handled by the BOD33 */
|
|
#define SUPC_BBPS_CONF_NONE (SUPC_BBPS_CONF_NONE_Val << SUPC_BBPS_CONF_Pos)
|
|
#define SUPC_BBPS_CONF_APWS (SUPC_BBPS_CONF_APWS_Val << SUPC_BBPS_CONF_Pos)
|
|
#define SUPC_BBPS_CONF_FORCED (SUPC_BBPS_CONF_FORCED_Val << SUPC_BBPS_CONF_Pos)
|
|
#define SUPC_BBPS_CONF_BOD33 (SUPC_BBPS_CONF_BOD33_Val << SUPC_BBPS_CONF_Pos)
|
|
#define SUPC_BBPS_WAKEEN_Pos 2 /**< \brief (SUPC_BBPS) Wake Enable */
|
|
#define SUPC_BBPS_WAKEEN (_U_(0x1) << SUPC_BBPS_WAKEEN_Pos)
|
|
#define SUPC_BBPS_PSOKEN_Pos 3 /**< \brief (SUPC_BBPS) Power Supply OK Enable */
|
|
#define SUPC_BBPS_PSOKEN (_U_(0x1) << SUPC_BBPS_PSOKEN_Pos)
|
|
#define SUPC_BBPS_MASK _U_(0x0000000F) /**< \brief (SUPC_BBPS) MASK Register */
|
|
|
|
/* -------- SUPC_BKOUT : (SUPC Offset: 0x24) (R/W 32) Backup Output Control -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t EN:2; /*!< bit: 0.. 1 Enable Output */
|
|
uint32_t :6; /*!< bit: 2.. 7 Reserved */
|
|
uint32_t CLR:2; /*!< bit: 8.. 9 Clear Output */
|
|
uint32_t :6; /*!< bit: 10..15 Reserved */
|
|
uint32_t SET:2; /*!< bit: 16..17 Set Output */
|
|
uint32_t :6; /*!< bit: 18..23 Reserved */
|
|
uint32_t RTCTGL:2; /*!< bit: 24..25 RTC Toggle Output */
|
|
uint32_t :6; /*!< bit: 26..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_BKOUT_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_BKOUT_OFFSET 0x24 /**< \brief (SUPC_BKOUT offset) Backup Output Control */
|
|
#define SUPC_BKOUT_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BKOUT reset_value) Backup Output Control */
|
|
|
|
#define SUPC_BKOUT_EN_Pos 0 /**< \brief (SUPC_BKOUT) Enable Output */
|
|
#define SUPC_BKOUT_EN_Msk (_U_(0x3) << SUPC_BKOUT_EN_Pos)
|
|
#define SUPC_BKOUT_EN(value) (SUPC_BKOUT_EN_Msk & ((value) << SUPC_BKOUT_EN_Pos))
|
|
#define SUPC_BKOUT_CLR_Pos 8 /**< \brief (SUPC_BKOUT) Clear Output */
|
|
#define SUPC_BKOUT_CLR_Msk (_U_(0x3) << SUPC_BKOUT_CLR_Pos)
|
|
#define SUPC_BKOUT_CLR(value) (SUPC_BKOUT_CLR_Msk & ((value) << SUPC_BKOUT_CLR_Pos))
|
|
#define SUPC_BKOUT_SET_Pos 16 /**< \brief (SUPC_BKOUT) Set Output */
|
|
#define SUPC_BKOUT_SET_Msk (_U_(0x3) << SUPC_BKOUT_SET_Pos)
|
|
#define SUPC_BKOUT_SET(value) (SUPC_BKOUT_SET_Msk & ((value) << SUPC_BKOUT_SET_Pos))
|
|
#define SUPC_BKOUT_RTCTGL_Pos 24 /**< \brief (SUPC_BKOUT) RTC Toggle Output */
|
|
#define SUPC_BKOUT_RTCTGL_Msk (_U_(0x3) << SUPC_BKOUT_RTCTGL_Pos)
|
|
#define SUPC_BKOUT_RTCTGL(value) (SUPC_BKOUT_RTCTGL_Msk & ((value) << SUPC_BKOUT_RTCTGL_Pos))
|
|
#define SUPC_BKOUT_MASK _U_(0x03030303) /**< \brief (SUPC_BKOUT) MASK Register */
|
|
|
|
/* -------- SUPC_BKIN : (SUPC Offset: 0x28) (R/ 32) Backup Input Control -------- */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef union {
|
|
struct {
|
|
uint32_t BKIN:8; /*!< bit: 0.. 7 Backup Input Value */
|
|
uint32_t :24; /*!< bit: 8..31 Reserved */
|
|
} bit; /*!< Structure used for bit access */
|
|
uint32_t reg; /*!< Type used for register access */
|
|
} SUPC_BKIN_Type;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
#define SUPC_BKIN_OFFSET 0x28 /**< \brief (SUPC_BKIN offset) Backup Input Control */
|
|
#define SUPC_BKIN_RESETVALUE _U_(0x00000000) /**< \brief (SUPC_BKIN reset_value) Backup Input Control */
|
|
|
|
#define SUPC_BKIN_BKIN_Pos 0 /**< \brief (SUPC_BKIN) Backup Input Value */
|
|
#define SUPC_BKIN_BKIN_Msk (_U_(0xFF) << SUPC_BKIN_BKIN_Pos)
|
|
#define SUPC_BKIN_BKIN(value) (SUPC_BKIN_BKIN_Msk & ((value) << SUPC_BKIN_BKIN_Pos))
|
|
#define SUPC_BKIN_MASK _U_(0x000000FF) /**< \brief (SUPC_BKIN) MASK Register */
|
|
|
|
/** \brief SUPC hardware registers */
|
|
#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__))
|
|
typedef struct {
|
|
__IO SUPC_INTENCLR_Type INTENCLR; /**< \brief Offset: 0x00 (R/W 32) Interrupt Enable Clear */
|
|
__IO SUPC_INTENSET_Type INTENSET; /**< \brief Offset: 0x04 (R/W 32) Interrupt Enable Set */
|
|
__IO SUPC_INTFLAG_Type INTFLAG; /**< \brief Offset: 0x08 (R/W 32) Interrupt Flag Status and Clear */
|
|
__I SUPC_STATUS_Type STATUS; /**< \brief Offset: 0x0C (R/ 32) Power and Clocks Status */
|
|
__IO SUPC_BOD33_Type BOD33; /**< \brief Offset: 0x10 (R/W 32) BOD33 Control */
|
|
__IO SUPC_BOD12_Type BOD12; /**< \brief Offset: 0x14 (R/W 32) BOD12 Control */
|
|
__IO SUPC_VREG_Type VREG; /**< \brief Offset: 0x18 (R/W 32) VREG Control */
|
|
__IO SUPC_VREF_Type VREF; /**< \brief Offset: 0x1C (R/W 32) VREF Control */
|
|
__IO SUPC_BBPS_Type BBPS; /**< \brief Offset: 0x20 (R/W 32) Battery Backup Power Switch */
|
|
__IO SUPC_BKOUT_Type BKOUT; /**< \brief Offset: 0x24 (R/W 32) Backup Output Control */
|
|
__I SUPC_BKIN_Type BKIN; /**< \brief Offset: 0x28 (R/ 32) Backup Input Control */
|
|
} Supc;
|
|
#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */
|
|
|
|
/*@}*/
|
|
|
|
#endif /* _SAML22_SUPC_COMPONENT_ */
|