Sensor-Watch/watch-library/watch/watch_private.c

/*
 * MIT License
 *
 * Copyright (c) 2020 Joey Castillo
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in all
 * copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
 * SOFTWARE.
 */

#include "tusb.h"

void _watch_init() {
    // disable the LED pin (it may have been enabled by the bootloader)
    watch_disable_digital_output(RED);

    // Use switching regulator for lower power consumption.
    SUPC->VREG.bit.SEL = 1;
    while(!SUPC->STATUS.bit.VREGRDY);

    // External wake depends on RTC; calendar is a required module.
    CALENDAR_0_init();
    calendar_enable(&CALENDAR_0);

    // Not sure if this belongs in every app -- is there a power impact?
    delay_driver_init();

    // set up state
    btn_alarm_callback = NULL;
    a2_callback = NULL;
    a4_callback = NULL;
}

void _watch_enable_usb() {
    // disable USB, just in case.
    hri_usb_clear_CTRLA_ENABLE_bit(USB);

    // reset flags and disable DFLL
    OSCCTRL->INTFLAG.reg = OSCCTRL_INTFLAG_DFLLRDY;
    OSCCTRL->DFLLCTRL.reg = 0;
    while (!(OSCCTRL->STATUS.reg & OSCCTRL_STATUS_DFLLRDY));

    // set the coarse and fine values to speed up frequency lock.
    uint32_t coarse =(*((uint32_t *)NVMCTRL_OTP5)) >> 26;
    OSCCTRL->DFLLVAL.reg = OSCCTRL_DFLLVAL_COARSE(coarse) |
                           OSCCTRL_DFLLVAL_FINE(0x200);
    // set coarse and fine steps, and multiplier (48 MHz = 32768 Hz * 1465)
    OSCCTRL->DFLLMUL.reg = OSCCTRL_DFLLMUL_CSTEP( 1 ) |
                           OSCCTRL_DFLLMUL_FSTEP( 1 ) |
                           OSCCTRL_DFLLMUL_MUL( 1465 );
    // set closed loop mode, chill cycle disable and USB clock recovery mode, and enable the DFLL.
    OSCCTRL->DFLLCTRL.reg = OSCCTRL_DFLLCTRL_MODE | OSCCTRL_DFLLCTRL_CCDIS | OSCCTRL_DFLLCTRL_ONDEMAND | OSCCTRL_DFLLCTRL_RUNSTDBY | OSCCTRL_DFLLCTRL_USBCRM | OSCCTRL_DFLLCTRL_ENABLE;
    while (!(OSCCTRL->STATUS.reg & OSCCTRL_STATUS_DFLLRDY));

    // assign DFLL to GCLK1
    GCLK->GENCTRL[1].reg = GCLK_GENCTRL_SRC(GCLK_GENCTRL_SRC_DFLL48M) | GCLK_GENCTRL_DIV(1) | GCLK_GENCTRL_GENEN;// | GCLK_GENCTRL_OE;
    while (GCLK->SYNCBUSY.bit.GENCTRL1);

    // assign GCLK1 to USB
    hri_gclk_write_PCHCTRL_reg(GCLK, USB_GCLK_ID, GCLK_PCHCTRL_GEN_GCLK1_Val | GCLK_PCHCTRL_CHEN);
    hri_mclk_set_AHBMASK_USB_bit(MCLK);
    hri_mclk_set_APBBMASK_USB_bit(MCLK);

    // USB Pin Init
    gpio_set_pin_direction(PIN_PA24, GPIO_DIRECTION_OUT);
    gpio_set_pin_level(PIN_PA24, false);
    gpio_set_pin_pull_mode(PIN_PA24, GPIO_PULL_OFF);
    gpio_set_pin_direction(PIN_PA25, GPIO_DIRECTION_OUT);
    gpio_set_pin_level(PIN_PA25, false);
    gpio_set_pin_pull_mode(PIN_PA25, GPIO_PULL_OFF);

    gpio_set_pin_function(PIN_PA24, PINMUX_PA24G_USB_DM);
    gpio_set_pin_function(PIN_PA25, PINMUX_PA25G_USB_DP);

    tusb_init();
}

// this function ends up getting called by printf to log stuff to the USB console.
int _write(int file, char *ptr, int len) {
    (void)file;
    if (hri_usbdevice_get_CTRLA_ENABLE_bit(USB)) {
        tud_cdc_n_write(0, (void const*)ptr, len);
        tud_cdc_n_write_flush(0);
        return len;
    }

    return 0;
}

// this method could be overridden to read stuff from the USB console? but no need rn.
int _read() {
    return 0;
}

void USB_Handler(void) {
    tud_int_handler(0);
}


// USB Descriptors and tinyUSB callbacks follow.

/*
 * The MIT License (MIT)
 *
 * Copyright (c) 2019 Ha Thach (tinyusb.org)
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 *
 */

#include "tusb.h"

/* A combination of interfaces must have a unique product id, since PC will save device driver after the first plug.
 * Same VID/PID with different interface e.g MSC (first), then CDC (later) will possibly cause system error on PC.
 *
 * Auto ProductID layout's Bitmap:
 *   [MSB]         HID | MSC | CDC          [LSB]
 */
#define _PID_MAP(itf, n)  ( (CFG_TUD_##itf) << (n) )
#define USB_PID           (0x4000 | _PID_MAP(CDC, 0) | _PID_MAP(MSC, 1) | _PID_MAP(HID, 2) | \
                           _PID_MAP(MIDI, 3) | _PID_MAP(VENDOR, 4) )

//--------------------------------------------------------------------+
// Device Descriptors
//--------------------------------------------------------------------+
tusb_desc_device_t const desc_device =
{
    .bLength            = sizeof(tusb_desc_device_t),
    .bDescriptorType    = TUSB_DESC_DEVICE,
    .bcdUSB             = 0x0200,

    // Use Interface Association Descriptor (IAD) for CDC
    // As required by USB Specs IAD's subclass must be common class (2) and protocol must be IAD (1)
    .bDeviceClass       = TUSB_CLASS_MISC,
    .bDeviceSubClass    = MISC_SUBCLASS_COMMON,
    .bDeviceProtocol    = MISC_PROTOCOL_IAD,

    .bMaxPacketSize0    = CFG_TUD_ENDPOINT0_SIZE,

    .idVendor           = 0xCafe,
    .idProduct          = USB_PID,
    .bcdDevice          = 0x0100,

    .iManufacturer      = 0x01,
    .iProduct           = 0x02,
    .iSerialNumber      = 0x03,

    .bNumConfigurations = 0x01
};

// Invoked when received GET DEVICE DESCRIPTOR
// Application return pointer to descriptor
uint8_t const * tud_descriptor_device_cb(void) {
  return (uint8_t const *) &desc_device;
}

//--------------------------------------------------------------------+
// Configuration Descriptor
//--------------------------------------------------------------------+

enum {
  ITF_NUM_CDC = 0,
  ITF_NUM_CDC_DATA,
  ITF_NUM_TOTAL
};

#define CONFIG_TOTAL_LEN    (TUD_CONFIG_DESC_LEN + TUD_CDC_DESC_LEN)

#define EPNUM_CDC_NOTIF   0x81
#define EPNUM_CDC_OUT     0x02
#define EPNUM_CDC_IN      0x82


uint8_t const desc_fs_configuration[] = {
  // Config number, interface count, string index, total length, attribute, power in mA
  TUD_CONFIG_DESCRIPTOR(1, ITF_NUM_TOTAL, 0, CONFIG_TOTAL_LEN, TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP, 100),

  // Interface number, string index, EP notification address and size, EP data address (out, in) and size.
  TUD_CDC_DESCRIPTOR(ITF_NUM_CDC, 4, EPNUM_CDC_NOTIF, 8, EPNUM_CDC_OUT, EPNUM_CDC_IN, 64),
};

// Invoked when received GET CONFIGURATION DESCRIPTOR
// Application return pointer to descriptor
// Descriptor contents must exist long enough for transfer to complete
uint8_t const * tud_descriptor_configuration_cb(uint8_t index) {
    (void) index; // for multiple configurations
    return desc_fs_configuration;
}

//--------------------------------------------------------------------+
// String Descriptors
//--------------------------------------------------------------------+

// array of pointer to string descriptors
char const* string_desc_arr [] =
{
  (const char[]) { 0x09, 0x04 }, // 0: is supported language is English (0x0409)
  "TinyUSB",                     // 1: Manufacturer
  "TinyUSB Device",              // 2: Product
  "123456",                      // 3: Serials, should use chip ID
  "TinyUSB CDC",                 // 4: CDC Interface
};

static uint16_t _desc_str[32];

// Invoked when received GET STRING DESCRIPTOR request
// Application return pointer to descriptor, whose contents must exist long enough for transfer to complete
uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid)
{
    (void) langid;

    uint8_t chr_count;

    if ( index == 0) {
        memcpy(&_desc_str[1], string_desc_arr[0], 2);
        chr_count = 1;
    } else {
        // Note: the 0xEE index string is a Microsoft OS 1.0 Descriptors.
        // https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-defined-usb-descriptors

        if ( !(index < sizeof(string_desc_arr)/sizeof(string_desc_arr[0])) ) return NULL;

        const char* str = string_desc_arr[index];

        // Cap at max char
        chr_count = strlen(str);
        if ( chr_count > 31 ) chr_count = 31;

        // Convert ASCII string into UTF-16
        for(uint8_t i=0; i<chr_count; i++)
        {
            _desc_str[1+i] = str[i];
        }
    }

    // first byte is length (including header), second byte is string type
    _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2);

    return _desc_str;
}